background image

Mechatronic flow sensor

SB1xxx SB2xxx SB3xxx SB4xxx SB5xxx SB6xxx SB7xxx SB8xxx SB9xxx

SB03xx

7

5 Mounting

CAUTION

During installation or in case of a fault (e.g. housing damage) media under high pressure or
hot media can leak from the system.

w

Risk of injury caused by pressure or burns.

u

Ensure that the system is free of pressure during installation.

u

Ensure that no media can leak at the mounting location during installation.

u

Equip the unit with suitable protection (e.g. cover) to avoid hazard to personnel from
leaking media.

5.1 Process connection

u

Avoid major changes of cross section on the inlet side. Use max. one connection size smaller.

u

Fit the unit in the pipe in accordance with the flow direction (arrow) and tighten at the spanner flats.

Do not clamp the housing in a vice.

IN

OUT

Fig. 1: Process connection

IN:

inlet

OUT:

outlet

Calming sections on the sensor's inlet or outlet side are not necessary.

The sensor can also prevent backflow.

The sensor head can be rotated by 360°.

5.2 Interference

u

The following minimum distances must be adhered to:

Distance between the sensor and ferromagnetic materials

≥ 30 mm *

Distance between the sensor and constant / alternating fields

≥ 500 mm

Distance between the sensor axes for side-by-side installation

≥ 50 mm

* The pipe may consist of ferromagnetic material.

Summary of Contents for SB03 Series
































Reviews: