background image

9

UK

 

Screw the filter cover again tightly.

The sensor is sufficiently protected against harsh ambient conditions (protection 

IP 67). The protection rating can be increased by a special accessory (order no. 

E30043).

8  Parameter setting

Parameters can be set before installation and set-up of the unit or during opera-

tion.

If you change parameters during operation, the operating principle of the 

plant will be influenced. 

 

Ensure that there will be no malfunctions in your plant.

• 

Parameter setting with PP2001 →operating instructions enclosed to PP2001.

8.1  Adjustable parameters

ASP

Analogue start point

Measured value at which 4 mA is provided.

AEP

Analogue end point

Measured value at which 20 mA is provided.

Minimum distance between ASP and AEP = 25% of the span.

HI 

LO

Min-Max memory for system pressure

• HI: displays the highest measured pressure.

• LO: displays the lowest measured pressure.

COF

Calibration offset

The internal measured value (operating value of the sensor) is offset against the 

real measured value.

• Setting range: -5 ... +5% of the value of the span (with scaling as factory setting 

(ASP = 0 bar and AEP = final value of measuring range) in steps of 0.1% of the 

value of the span.

CAr

Calibration reset

Resets the calibration set by COF.

dAA

Damping for the analogue output

Pressure peaks of short duration or high frequency can be filtered out.

dAA-value = response time between pressure change and change of the switch-

ing status in milliseconds (ms).

• 

Setting range: 0 (= dAA is not active) / 0.1 s / 0.5 s / 2 s.

Uni

Display unit

The measured values and values for ASP / AEP can be indicated in the following 

units:

bar, mbar, PSI, MPa, kPa, inH2O (only PL2058), mmWS (only PL2058).

Summary of Contents for PL205 Series












Reviews: