background image

26

9.4  User settings (optional)
9.4.1  Carry out zero point calibration 

 

Select [COF] and set a value between -5 % and 5 % of the final value of 

the measuring range� The internal measured value "0" is shifted by this 

value�

Alternatively: automatic adjustment of the offset in the range 0 bar ± 5 %�

 

Make sure that no pressure is applied to the system�

 

Press [Mode/Enter] until [tCOF] appears�

 

Press and hold down [Set]�

 

> The current offset value (in %) flashes briefly�

 

> The current system pressure is displayed�

 

Release [Set]�

 

Briefly press [Mode/Enter] (= to confirm the new offset value)�

9.4.2  Set output status in fault condition

 

Select [FOU1] and set the value:

 -[On] = output 1 switches ON in case of a fault�

 -[OFF] = output 1 switches OFF in case of a fault�

 -[OU] = output 1 switches irrespective of a fault as defined with the 

parameters SP1, rP1 and OU1�

 

Select [FOU2] and set the value:

 -[On] = output 2 switches ON in case of a fault, the analogue signal 

goes to the upper final value�

 -[OFF] = output 2 switches OFF in case of a fault, the analogue signal 

goes to the lower final value�

 -[OU] = output 2 switches irrespective of the fault as defined with the 

parameters SP2, rP2, OU2� The analogue signal corresponds to the 

measured value�

Fault indications → 10.3

9.4.3  Set delay time for the switching outputs

[dS1] / [dS2] = switch-on delay for OUT1 / OUT2�

[dr1] / [dr2] = switch-off delay for OUT1 / OUT2�

 

Select [dS1], [dS2], [dr1] or [dr2] and set a value between 0�1 and 50 s 

(at 0�0 the delay time is not active)�

9.4.4  Set output logic for the switching outputs

 

Select [P-n] and set [PnP] or [nPn]�

Summary of Contents for PI22 Series




































Reviews: