background image

O1D110

Photoelectric distance sensor

20

w

[WAIT] is displayed while the repeatability [rEPr] is calculated.

w

The sampling rate [rATE] and repeatability [rEPr] are displayed alternately.

10.3.2 Setting of the repeatability

u

Select [TEAC] and keep [SET] pressed until [WAIT] is displayed.

w

[rATE] and [rEPr] are displayed alternately.

u

If [rEPr] is displayed: Press [SET] until the preset repeatability value flashes.

u

Enter a value incrementally by pressing [SET] repeatedly.

u

Confirm with [MODE/ENTER].

w

[WAIT] is displayed while the sampling rate [rATE] is calculated.

w

The sampling rate [rATE] and repeatability [rEPr] are displayed alternately.

10.4 Extended functions

10.4.1 Set the delay time for switching outputs

u

Select [EF].

u

Press [SET] to change to the menu [EF].

u

Select parameter with [MODE/ENTER]:

u

[dSx] = switch-on delay; [drx] = switch-off delay

u

Set the parameter value with [SET]:

u

Setting range [s]: 0 / 0.1...5 s in steps of 0.1 s\(0 = delay time is not active)

u

Confirm with [MODE/ENTER].

10.4.2 Setting of the fault suppression time for switching output / analogue
output

u

Select [EF].

u

Press [SET] to change to the menu [EF].

u

Select[dFo] (old designation: [dAP]).

u

Set the parameter value with [SET]: Setting range [s]: 0.0...0.1...0.2...0.5...1...2...5.

u

Confirm with [MODE/ENTER].

With [dFo], the error types "too much light" and "not enough light" are suppressed. (

Ò

 Error

indications 

/

 22)

10.4.3 Reset all parameters to factory setting

u

Select [EF].

u

Press [SET] to change to the menu [EF].

u

Select [rES] and keep [SET] pressed until [----] is displayed.

u

Confirm with [MODE/ENTER].

w

The unit changes to the Run mode.

Summary of Contents for O1D110
























Reviews: