background image

O1D110

Photoelectric distance sensor

18

[Hnc] = hysteresis function / normally closed

[Fno] = window function / normally open

[Fnc] = window function / normally closed

[I] = current output analogue 4...20 mA:

[U] = voltage output analogue 0...10 V

u

Confirm with [MODE/ENTER].

10.2.9 Setting of the switch point for hysteresis function OUT2

u

Select [OU2], [Hno] or [Hnc].

u

Confirm with [MODE/ENTER].

u

Select [SP2] and set the switch point.

u

Confirm with [MODE/ENTER].

Hysteresis function (

Ò

 

/

 15)

10.2.10 Setting of the switch points for window function OUT2

u

Select [OU2], [Fno] or [Fnc].

u

Confirm with [MODE/ENTER].

u

Select [nSP2] and set the switch point “near”.

u

Confirm with [MODE/ENTER].

u

Select [FSP2] nd set the switch point "far".

u

Confirm with [MODE/ENTER].

Window function (

Ò

 

/

 16)

10.2.11 Scaling of the measuring range (analogue output)

u

Select [OU2], [I] or [U].

u

Confirm with [MODE/ENTER].

u

Select [ASP] and set the "Analogue start point". With [ASP]], you define at which measured value
the output signal is 4 mA / 0 V.

u

Confirm with [MODE/ENTER].

u

Select [AEP] and set the "Analogue end point". With [AEP]], you define at which measured value
the output signal is 20 mA / 10 V. It can also be selected so that it is located before [ASP]. This
implements a falling edge.

u

Confirm with [MODE/ENTER].

Minimum distance between [ASP] and [AEP]: 100 mm

When the minimum distance is not reached, the error message [SIZE] will be displayed.

Summary of Contents for O1D110
























Reviews: