manualshive.com logo in svg

IFM E30398, Operating Instructions Manual, Page: 19 / 19

Share
Download
IFM E30398 Operating Instructions Manual Download Page 19

19

UK

8  Troubleshooting

For all errors the following applies:
•  The parameter set in the memory plug remains� It is not damaged by faulty 

reading or writing� 

•  The error remains until it has been removed�
•  If the memory plug detects an error, the transmission of the sensor output 

(OUT1, pin 4) to the higher-level system is stopped�

Error in data processing
Cause of the fault

Corrective measures

Sensor cable removed during transmission�

 

►

Connect the sensor cable to the memory 

plug again�

Unknown sensor connected, e�g� 

• IO-Link 1�0 sensor of another 

manufacturer�

• Sensor not equipped with IO-Link �

 

►

Connect an IO-Link 1�0 sensor from ifm 

electronic�

 

►

Connect an IO-Link 1�1 sensor�

The sensor does not support any saving 

of data�

 

►

Connect a sensor supporting IO-Link 

and saving of data (→ data sheet of the 

sensor)�

Sensor locked, writing impossible�

 

►

Unlock the sensor or connect an 

unlocked sensor�

The identification of the connected sensor does not correspond to the parameter set in the 

memory plug�
Cause of the fault

Corrective measures

The connected sensor is neither of the 

same type nor compatible�

 

►

Connect a sensor of the same type (= 

sensor with the same IO-Link device ID) or 

another compatible sensor�

More information at www�ifm�com

Summary of Contents for E30398




















Reviews:

No comments