manualshive.com logo in svg

IFM E30398, Operating Instructions Manual, Page: 15 / 19

Share
Download
IFM E30398 Operating Instructions Manual Download Page 15

15

UK

6.6.2  Read and edit the data stored on the memory plug 

 

►

Connect the memory plug to the USB IO-Link master�

 

►

Click on [ ]�

 

> The parameter list of the connected memory plug is loaded into the software�

 

►

Click on [ ] if this is supported by the device�

 

> All stored parameters are displayed and can be edited�

 

►

Click on [ ]�

 

> The parameter list of the connected memory plug is displayed�

6.6.3  Restore the factory setting of the memory plug

 

►

Connect the memory plug to the IO-Link master�

 

►

Click on [ ]�

 

> The parameter list of the connected memory plug is loaded into the software�

 

►

Click on [

]�

 

> The factory setting of the memory plug is restored�

6.7  Operation indication

No supply voltage�

Memory plug without saved parameter set in the [Write protected] mode, 

factory setting� 

Memory plug with saved parameter set in the [Write protected] mode�

Memory plug without saved parameter set in the [Read/Write] mode�

Summary of Contents for E30398




















Reviews:

No comments