background image

Pulse stretcher

DP2402

15

8 Menu

8.1 General

Irrespective of the operating mode (standard IO mode or IO-Link device) there are two options to set
the parameters of the unit:

directly on the unit via the menu Parameter setting (

Ò

 

/

 19)

or via an IO-Link tool

Access via an IO-Link tool has a higher priority than parameter setting via the menu.

Parameter cloning and parameter setting backup is possible with an IO-Link tool.

Some parameters can only be set via the IO-Link interface:
Parameters adjustable via IO-Link.

If the unit was locked via IO-Link, it can also only be unlocked via the IO-Link interface:
Locking / unlocking (

Ò

 

/

 20).

8.2 Menu structure

---

---

ou1

OFF no

nc

-Edg

dln1

PULS Edg

OUt1

dS1

0...9999

dr1

0...9999

h.t1

1...9999

ou2

OFF no

nc

-Edg

dln2

PULS Edg

OUt2

dS2

0...9999

dr2

0...9999

h.t2

1...9999

1

2

EF

rES

---

Fig. 8: Parameters

1:

Operating mode: Menu (

Ò

 

/

 15)

2:

Parameters of the main menu: Parameters for OUT1 (

Ò

 

/

 16), Parameters for OUT2 (

Ò

 

/

 16) and Parameters of the

extended functions (EF) (

Ò

 

/

 17)

Parameter list and factory settings: Factory settings (

Ò

 

/

 24)

8.3 Parameters of the main menu

8.3.1 OUt1 ─ output OUT1

The parameter opens the menu of the settings for OUT1.

Summary of Contents for DP2402

























Reviews: