manualshive.com logo in svg

IFM Electronic AL1100, Operating Instructions Manual

Share
Download
IFM Electronic AL1100 Operating Instructions Manual Download Page 14

14 

ifm

 Operating Instructions IO-Link Master with PROFINET interface StandardLine 4 Ports IP 65 / IP 66 / IP 67 (AL1100) 

05 / 2018 

Electrical connection 

Remarks 

 

6

 

Electrical connection 

 

Remarks .................................................................................................................................................14 
Ethernet ports .........................................................................................................................................15 
IO-Link ports ...........................................................................................................................................15 
Connect the device .................................................................................................................................17 

22017 

> 

 

6.1

 

Remarks 

18076 

  

 

A qualified electrician must connect the unit. 
►  Observe the national and international regulations for the installation of electrical 

equipment. 

Device is only suitable for operation on SELV/PELV voltages. 
►  Observe the information concerning IO-Link circuits (→ 

IO-Link circuits

 (

→ p. 

16

))! 

The device contains components that can be damaged or destroyed by electrostatic discharge 
(ESD). 
►  Observe the required safety measures against electrostatic discharge! 
The IP rating depends on the individual protection ratings of the unit, the applied connection 
elements and the corresponding protective covers. 
►  For UL applications: For connecting the device and the IO-Link devices use UL certificated 

cables of category CYJV or PVVA with a minimum temperature rating of 100°C. 

►  Depending on the mounting conditions, cables must be provided with a strain relief to 

avoid unacceptable loads on the mounting points and M12 connections. 

►  Make sure that the M12 connection parts are correctly seated and mounted correctly. The 

specified protection rating can not be guaranteed if this is not observed. 

Wiring: 

→ 

Technical data

 (

→ p. 

48

) 

  

 

The communication interfaces are seperated from the device supply according to EN61010-1 
considering basis isolation as secondary circuit with maximum 30 V DC derived from the 
applied voltage up to 300 V of overvoltage category II. The communication interfaces are 
designed for a network environment 0 according to IEC TR62102. 

  

Summary of Contents for AL1100






























































Reviews:

No comments

Brands by name

Popular brands

Load more brands