manualshive.com logo in svg

IEI Technology WSB-G41A-R11, User Manual

Share
Download
IEI Technology WSB-G41A-R11 User Manual Download Page 67

 

 

WSB-G41A CPU Card 

Page 55

Step 2: 

Align the VGA connector

. Align the male DB-15 connector on the VGA screen 

cable with the female DB-15 connector on the external peripheral interface. 

Step 3: 

Insert the VGA connector

. 

Once the connectors are properly aligned with the 

insert the male connector from the VGA screen into the female connector on the 

WSB-G41A. See 

Figure 4-19

. 

 

Figure 4-19: VGA Connector 

Step 4: 

Secure the connector

. Secure the DB-15 VGA connector from the VGA 

monitor to the external interface by tightening the two retention screws on either 

side of the connector.

 

Step 0:

 

4.7 Software Installation 

All the drivers for the WSB-G41A are on the CD that came with the system. To install the 

drivers, please follow the steps below. 

Step 1: 

Insert the CD into a CD drive connected to the system. 

Summary of Contents for WSB-G41A-R11



























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands