IEI Technology WSB-G41A-R11 User Manual Download Page 54

Page: 54 / 122

WSB-G41A CPU Card

Page 42

Step 3:

Mount the cooling kit

. Gently place the cooling kit on top of the CPU. Make

sure the four threaded screws on the corners of the cooling kit properly pass

through the predrilled holes on the bottom of the PCB.

Step 4:

Secure the cooling kit

. From the solder side of the PCB, align the support

bracket to the screw threads on heat sink that were inserted through the PCB

holes. (See

Figure 4-6

)

Figure 4-6: Securing the Heat sink to the WSB-G41A

Step 5:

Tighten the screws

. Use a screwdriver to tighten the four screws. Tighten each

nut a few turns at a time and do not over-tighten the screws.

Step 6:

Connect the fan cable

. Connect the cooling kit fan cable to the fan connector

on the WSB-G41A. Carefully route the cable and avoid heat generating chips

and fan blades.

Step 0:

Summary of Contents for WSB-G41A-R11



























































































































Search results

Summary of Contents for WSB-G41A-R11

Reviews:

Brands by name

Popular brands

IEI Technology WSB-G41A-R11, User Manual

Search results

Summary of Contents for WSB-G41A-R11

Reviews:

Brands by name

Popular brands