IEI Technology WSB-G41A-R11 User Manual Download Page 108

Page: 108 / 122

WSB-G41A CPU Card

Page 96

Below is a list of BIOS configuration options in the BIOS chapter.

System Overview .................................................................................................................61

System Time [xx:xx:xx] .......................................................................................................62

System Date [xx/xx/xx] ........................................................................................................62

ATA/IDE Configurations [Enhanced] .................................................................................64

Configure SATA Channels [Before PATA] ........................................................................65

IDE Master and IDE Slave....................................................................................................65

Auto-Detected Drive Parameters........................................................................................66

Type [Auto] ...........................................................................................................................67

LBA/Large Mode [Auto].......................................................................................................67

Block (Multi Sector Transfer) [Auto] ..................................................................................67

PIO Mode [Auto]...................................................................................................................68

DMA Mode [Auto].................................................................................................................68

S.M.A.R.T [Auto]...................................................................................................................69

32Bit Data Transfer [Enabled].............................................................................................69

Floppy A................................................................................................................................70

Parallel Port Address [378] .................................................................................................70

Parallel Port Mode [Normal]................................................................................................71

Parallel Port IRQ [IRQ7].......................................................................................................71

Serial Port1 Address [3F8/IRQ4] ........................................................................................71

Serial Port1 Mode [Normal].................................................................................................72

Serial Port2 Address [2F8/IRQ3] ........................................................................................72

Serial Port2 Mode [Normal].................................................................................................72

CPU FAN Mode Setting [Full On Mode] .............................................................................73

Temp. Limit of OFF [000].....................................................................................................74

Temp. Limit of Start [020]....................................................................................................74

Start PWM [070]....................................................................................................................74

Slope PWM [0.5 PWM] .........................................................................................................75

Fan PWM Control [100]........................................................................................................75

Hardware Health Configuration ..........................................................................................75

Suspend Mode [S1(POS)]....................................................................................................77

Restore on AC Power Loss [Last State] ............................................................................78

Power Button Mode [On/Off]...............................................................................................78

Resume on Keyboard/Mouse [Disabled] ...........................................................................79

Summary of Contents for WSB-G41A-R11



























































































































Search results

Summary of Contents for WSB-G41A-R11

Reviews:

Brands by name

Popular brands

IEI Technology WSB-G41A-R11, User Manual

Search results

Summary of Contents for WSB-G41A-R11

Reviews:

Brands by name

Popular brands