manualshive.com logo in svg

IEI Technology WSB-G41A-R11, User Manual

Share
Download
IEI Technology WSB-G41A-R11 User Manual Download Page 53

 

 

WSB-G41A CPU Card 

Page 41

4.3.2 Cooling Kit Installation 

 WARNING: 

DO NOT use the original Intel® heat sink and fan. A proprietary one is 

recommended. 

 

 

Figure 4-5: Cooling Kits 

The cooling kit can be bought from IEI. The cooling kit has a heatsink and fan. 

 WARNING: 

Do not wipe off (accidentally or otherwise) the pre-sprayed layer of 

thermal paste on the bottom of the heat sink. The thermal paste 

between the CPU and the heat sink is important for optimum heat 

dissipation. 

To install the cooling kit, follow the instructions below. 

Step 1: 

Place the cooling kit onto the socket LGA775 CPU

. Make sure the CPU 

cable can be properly routed when the cooling kit is installed. 

Step 2: 

Properly align the cooling kit

. Make sure the four spring screw fasteners can 

pass through the pre-drilled holes on the PCB. 

Summary of Contents for WSB-G41A-R11



























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands