IEI Technology WAFER-945GSELVDS2-N270-R10 User Manual Download Page 89

Page: 89 / 140

WAFER-945GSELVDS2

Page 77

Legacy IDE Channels [PATA Pri, SATA Sec]

SATA Only

Only the SATA drives are enabled.

PATA Pri, SATA Sec

EFAULT

The IDE drives are enabled on the Primary

IDE channel. The SATA drives are enabled on

the Secondary IDE channel.

PATA Pri., PATA Sec

The IDE drives are enabled on the primary

and secondary IDE channels. SATA drives

are disabled.

IDE Master and IDE Slave

When entering setup, BIOS auto detects the presence of IDE devices. BIOS displays the

status of the auto detected IDE devices. The following IDE devices are detected and are

shown in the

IDE Configuration

menu:

Primary

IDE

Master

Primary

IDE

Slave

5.3.2.1 IDE Master, IDE Slave

Use the

IDE Master

and

IDE Slave

configuration menu to view both primary and

secondary IDE device details and configure the IDE devices connected to the system.

BIOS SETUP UTILITY

Main

Advanced

PCIPNP

Boot

Security

Chipset

Exit

Primary IDE Master

⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯

Device :Not Detected

Type

[Auto]

LBA/Large Mode

[Auto]

Block (Multi-Sector Transfer)

[Auto]

PIO Mode

[Auto]

DMA Mode

[Auto]

S.M.A.R.T. [Auto]
32Bit Data Transfer

[Enabled]

Select the type of device
connected to the system

ÅÆ

Select

Screen

↑

↓

Select

Item

Enter Go to SubScreen
F1 General

Help

F10

Save and Exit

ESC Exit

BIOS Menu 5: IDE Master and IDE Slave Configuration

Summary of Contents for WAFER-945GSELVDS2-N270-R10













































































































































Search results

Summary of Contents for WAFER-945GSELVDS2-N270-R10

Reviews:

Brands by name

Popular brands

IEI Technology WAFER-945GSELVDS2-N270-R10, User Manual

Search results

Summary of Contents for WAFER-945GSELVDS2-N270-R10

Reviews:

Brands by name

Popular brands