manualshive.com logo in svg

IEI Technology WAFER-945GSELVDS2-N270-R10, User Manual

Share
Download
IEI Technology WAFER-945GSELVDS2-N270-R10 User Manual Download Page 54

 

 

WAFER-945GSELVDS2

Page 42 

4.2 Installation Considerations 

 NOTE: 

The following installation notices and installation considerations should 

be read and understood before the WAFER-945GSELVDS2 is 

installed. All installation notices pertaining to the installation of the 

WAFER-945GSELVDS2 should be strictly adhered to. Failing to 

adhere to these precautions may lead to severe damage of the 

WAFER-945GSELVDS2 and injury to the person installing the 

motherboard. 

4.2.1 Installation Notices 

 WARNING: 

The installation instructions described in this manual should be 

carefully followed in order to prevent damage to the 

WAFER-945GSELVDS2, WAFER-945GSELVDS2 components and 

injury to the user. 

Before and during the installation please 

DO

 the following: 

ƒ

 

Read the user manual: 

o

 

The user manual provides a complete description of the 

WAFER-945GSELVDS2 installation instructions and configuration 

options. 

ƒ

 

Wear an electrostatic discharge cuff (ESD): 

o

 

Electronic components are easily damaged by ESD. Wearing an ESD cuff 

removes ESD from the body and helps prevent ESD damage. 

ƒ

 

Place the WAFER-945GSELVDS2 on an antistatic pad: 

o

 

When installing or configuring the motherboard, place it on an antistatic 

pad. This helps to prevent potential ESD damage. 

Summary of Contents for WAFER-945GSELVDS2-N270-R10













































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands