manualshive.com logo in svg

IEI Technology WAFER-945GSELVDS2-N270-R10, User Manual

Share
Download
IEI Technology WAFER-945GSELVDS2-N270-R10 User Manual Download Page 68

 

 

WAFER-945GSELVDS2

Page 56 

4.7.2 Motherboard Installation 

To install the WAFER-945GSELVDS2 motherboard into the chassis please refer to the 

reference material that came with the chassis. 

4.8 Internal Peripheral Device Connections 

Install the following cables to use the internal devices listed. 

4.8.1 Audio Kit Installation 

The Audio Kit that came with the WAFER-945GSELVDS2 connects to the audio 

connector on the WAFER-945GSELVDS2. The audio kit consists of three audio jacks. 

Mic-in connects to a microphone. Line-in provides a stereo line-level input to connect to 

the output of an audio device. Line-out, a stereo line-level output, connects to two 

amplified speakers. To install the audio kit, please refer to the steps below: 

Step 1: 

Locate the audio connector

. The location of the 10-pin audio connector is 

shown in 

Chapter 3

. 

Step 2: 

Align pin 1

. Align pin 1 on the on-board connector with pin 1 on the audio kit 

connector. Pin 1 on the audio kit connector is indicated with a white dot. 

Summary of Contents for WAFER-945GSELVDS2-N270-R10













































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands