IEI Technology NANO-PV-D510A User Manual Download Page 83

Page: 83 / 169

NANO-PV-D510A User Manual

Page 69

Enhanced D

EFAULT

Configures the on-board ATA/IDE controller to be in

Enhanced mode. In this mode, IDE channels and SATA

channels are separated. This mode supports up to 6

storage devices. Some legacy OS do not support this

mode.

Configure SATA as [IDE]

Use the

Configure SATA as

option to configure SATA devices as normal IDE devices.

IDE D

EFAULT

Configures SATA devices as normal IDE device.

AHCI

Configures SATA devices as an ACHI device.

IDE Master and IDE Slave

When entering setup, BIOS automatically detects the presence of IDE devices. BIOS

displays the status of the auto detected IDE devices. The following IDE devices are

detected and are shown in the

IDE Configuration

menu:

Primary

IDE

Master

Primary

IDE

Slave

Secondary IDE Master

Secondary IDE Slave

Third IDE Master

Third IDE Slave

The

IDE Configuration

menu (

BIOS Menu 4

) allows changes to the configurations for the

IDE devices installed in the system. If an IDE device is detected and one of the above

listed four BIOS configuration options are selected, the IDE configuration options shown in

Section 5.3.2.1

appear.

5.3.2.1 IDE Master, IDE Slave

Use the

IDE Master

and

IDE Slave

configuration menu to view both primary and

secondary IDE device details and configure the IDE devices connected to the system.

Summary of Contents for NANO-PV-D510A










































































































































































Search results

Summary of Contents for NANO-PV-D510A

Reviews:

IEI Technology NANO-PV-D510A, User Manual, Page: 83 / 169

Search results

Summary of Contents for NANO-PV-D510A

Reviews: