IEI Technology NANO-PV-D510A User Manual Download Page 144

Page: 144 / 169

NANO-PV-D510A User Manual

Page 130

Step 11:

When the image creation completes, a screen prompts as shown in

Figure B-17

Click

Continue

and close the Ghost window to exit the program.

Figure B-17: Image Creation Complete

Step 12:

The recovery tool main menu window is shown as below. Press any key to

reboot the system.

Figure B-18: Press Any Key to Continue

B.3 Setup Procedure for Linux

The initial setup procedures for Linux system are mostly the same with the procedure for

Microsoft Windows. Please follow the steps below to setup recovery tool for Linux OS.

Step 1:

Hardware and BIOS setup

. Refer to

Section B.2.1

Step 2:

Install Linux operating system

. Make sure to install GRUB (v0.97 or earlier)

MBR type and Ext3 partition type. Leave enough space on the hard drive to

create the recover partition later.

Summary of Contents for NANO-PV-D510A










































































































































































Search results

Summary of Contents for NANO-PV-D510A

Reviews:

IEI Technology NANO-PV-D510A, User Manual, Page: 144 / 169

Search results

Summary of Contents for NANO-PV-D510A

Reviews: