IEI Technology NANO-PV-D510A User Manual Download Page 108

Page: 108 / 169

NANO-PV-D510A User Manual

Page 94

Disabled

USB 2.0 controller disabled

Enabled D

EFAULT

USB 2.0 controller enabled

Legacy USB Support [Enabled]

Use the

Legacy USB Support

BIOS option to enable USB mouse and USB keyboard

support.

Normally if this option is not enabled, any attached USB mouse or USB keyboard does not

become available until a USB compatible operating system is fully booted with all USB

drivers loaded. When this option is enabled, any attached USB mouse or USB keyboard

can control the system even when there is no USB driver loaded onto the system.

Disabled

Legacy USB support disabled

Enabled D

EFAULT

Legacy USB support enabled

Auto

Legacy USB support disabled if no USB devices are

connected

USB2.0 Controller Mode [HiSpeed]

Use the

USB2.0 Controller Mode

option to set the speed of the USB2.0 controller.

FullSpeed

The controller is capable of operating at 12 Mb/s

HiSpeed D

EFAULT

The controller is capable of operating at 480 Mb/s

5.3.8.1 USB Mass Storage Device Configuration

Use the

USB Mass Storage Device Configuration

menu (

BIOS Menu 14

) to configure

USB mass storage class devices.

Summary of Contents for NANO-PV-D510A










































































































































































Search results

Summary of Contents for NANO-PV-D510A

Reviews:

IEI Technology NANO-PV-D510A, User Manual, Page: 108 / 169

Search results

Summary of Contents for NANO-PV-D510A

Reviews: