IEI Technology NANO-PV-D510A User Manual Download Page 103

Page: 103 / 169

NANO-PV-D510A User Manual

Page 89

Resume on Keyboard/Mouse [Disabled]

Use the

Resume on Keyboard/Mouse

BIOS option to enable activity on either the

keyboard or mouse to rouse the system from a suspend or standby state. That is, the

system is roused when the mouse is moved or a button on the keyboard is pressed.

Disabled D

EFAULT

Wake event not generated by activity on the

keyboard or mouse

Resume On

KeyBoard

Wake event generated by activity on the keyboard

Resume On

Mouse

Wake event generated by activity on the mouse

Enabled

Wake event generated by activity on the keyboard or

mouse

Resume on PCI-Express WAKE# [Enabled]

The

Resume on PCI-Express WAKE#

BIOS option specifies if the system is roused from

a suspended or standby state when there is activity on the PCI-Express bus.

Disabled

Wake event not generated by PCI-Express activity

Enabled D

EFAULT

Wake event generated by PCI-Express activity

RI Resume [Disabled]

Use the

RI Resume

BIOS option to enable activity on the RI (ring in) modem line to rouse

the system from a suspend or standby state. That is, the system will be roused by an

incoming call on a modem.

Disabled D

EFAULT

Wake event not generated by an incoming call

Enabled

Wake event generated by an incoming call

RTC Resume [Disabled]

Use the

RTC Resume

option to specify the time the system should be roused from a

suspended state.

Summary of Contents for NANO-PV-D510A










































































































































































Search results

Summary of Contents for NANO-PV-D510A

Reviews:

IEI Technology NANO-PV-D510A, User Manual, Page: 103 / 169

Search results

Summary of Contents for NANO-PV-D510A

Reviews: