manualshive.com logo in svg

IEI Technology KINO-690S1, User Manual, Page: 175 / 229

Share
Download
IEI Technology KINO-690S1 User Manual Download Page 175

 

 

KINO-690S1 Mini-ITX Motherboard

Page 157

7.1 Available Software Drivers 

 NOTE: 

The content of the CD may vary throughout the life cycle of the product 

and is subject to change without prior notice. Visit the IEI website or 

contact technical support for the latest updates. 

The following drivers can be installed on the system: 

 

AMD chipset driver 

 

LAN driver 

 

Audio driver 

Installation instructions are given below. 

7.2 Driver CD Auto-run 

All the drivers for the KINO-690S1 are on the CD that came with the system. To install the 

drivers, please follow the steps below. 

Step 1: 

Insert the CD into a CD drive connected to the system. 

 NOTE: 

If the system does not initiate the "autorun" program when the CD is 

inserted, click the 

Start

 button, select 

Run

, then type 

X:\autorun.exe

 

(where 

X:\

 is the system CD drive) to access the IEI Driver CD main 

menu. 

Step 2: 

The driver main menu appears (

Figure 7-1

). 

Summary of Contents for KINO-690S1






































































































































































































































Reviews:

No comments