IEI Technology KINO-690S1 User Manual Download Page 130

Page: 130 / 229

KINO-690S1 Mini-ITX Motherboard

Page 112

Normal

EFAULT

Serial Port 2 mode is normal

IrDA

Serial Port 2 mode is IrDA

ASK IR

Serial Port 2 mode is ASK IR

Serial Port3 Address [3E8]

Use the

Serial Port3 Address

option to select the base addresses for serial port 3

Disabled

No base address is assigned to serial port 3

3E8 D

EFAULT

Serial port 3 I/O port address is 3E8

2E8

Serial port 3 I/O port address is 2E8

338

Serial port 3 I/O port address is 338

238

Serial port 3 I/O port address is 238

Select RS232 or RS422/RS485 [RS232]

Use the

Select RS232 or RS422/RS485

option to specify the serial port protocol being

used.

RS232 D

EFAULT

The RS-232 serial communications protocol is used

RS422/RS485 D

EFAULT

The RS-422/485 serial communications protocol is

used

Serial Port4 Address [2E8]

Use the

Serial Port4 IRQ

option to select the interrupt address for serial port 4.

Disabled

No base address is assigned to serial port 3

3E8

Serial port 4 I/O port address is 3E8

2E8 D

EFAULT

Serial port 4 I/O port address is 2E8

Summary of Contents for KINO-690S1






































































































































































































































Search results

Summary of Contents for KINO-690S1

Reviews:

IEI Technology KINO-690S1, User Manual, Page: 130 / 229

Search results

Summary of Contents for KINO-690S1

Reviews: