IEI Technology DM series User Manual Download Page 96

Page: 96 / 128

DM Series Monitor

Page 82

7.1 Introduction

The touch panel controller enables analog resistive touch panels for four-wire, five-wire &

eight-wire models. The controller directly communicates with the PC system through the

touch panel communications interface. The controller design is superior in sensitivity,

accuracy, and friendly operation. The touch panel driver emulates the left mouse button

and the right mouse button functions.

The touch panel driver supports the following operating systems:

Microsoft

Windows

versions:

Microsoft

Windows

2000

Microsoft

Windows

Microsoft

Windows

2003

Microsoft

Windows

2008

Microsoft

Windows

Vista

Microsoft

Windows

Microsoft

Windows

CE versions:

Microsoft

Windows

CE 4.2

Microsoft

Windows

CE 5.0

Microsoft

Windows

CE 6.0

Linux Kernel 2.6

DOS

Driver installation is described below.

7.2 RS-232 or USB Touch Screen

Before installing the driver, connect the DM Series monitor to the motherboard. The DM

Series monitors support touch screen modality through an RS-232 or USB interface

connection. Decide through which interface the touch screen is to be controlled.

RS-232 Interface:

If the touch screen interface connection is an RS-232

connection, connect the RS-232 connector on the single board computer to

the DB-9 connector of the DM Series monitor.

Summary of Contents for DM series

































































































































Search results

Summary of Contents for DM series

Reviews:

IEI Technology DM series, User Manual, Page: 96 / 128

Search results

Summary of Contents for DM series

Reviews: