manualshive.com logo in svg

IEI Technology DM series, User Manual, Page: 76 / 128

Share
Download
IEI Technology DM series User Manual Download Page 76

 

 

DM Series Monitor

Page 62 

5.5.2.1 Standard Cabinet and Rack Installation 

The standard cabinet/rack mounting procedure applies to the following DM series LCD 

monitors: 

ƒ

 DM-170 

ƒ

 DM-150 

ƒ

 DM-121 

ƒ

 DM-104 

To mount the DM series LCD monitor into a cabinet/rack, please follow the steps below. 

Step 1: 

The back of the metal frame surrounding the DM series LCD monitor has 

several retention screw holes for a cabinet/rack installation bracket. 

 NOTE: 

When purchasing a cabinet/rack installation bracket, make sure it is 

compatible with both the monitor and the cabinet/rack into which the 

monitor is installed. 

Step 2: 

Slide the monitor through the cabinet/rack bracket until the rear side of the 

monitor frame is flush against the front of the bracket. 

Step 3: 

Make sure the retention screw holes at the rear of the monitor frame are aligned 

with the retention screw holes in the cabinet/rack bracket. 

Step 4: 

Secure the cabinet/rack bracket to the monitor by inserting and tightening the 

retention screws (

5

Figure 5-18

).  

Summary of Contents for DM series

































































































































Reviews:

No comments