manualshive.com logo in svg

IEI Technology DM series, User Manual, Page: 75 / 128

Share
Download
IEI Technology DM series User Manual Download Page 75

 

 

DM Series Monitor 

Page 61

Figure 5-17: DM-65 Panel Mounting 

Step 3: 

Tighten the panel retention screws that pass through the panel mounting clips 

until the plastic caps at the front of all the screws are firmly secured to the panel 

(

5

Figure 5-17

).

Step 0:

 

5.5.2 Cabinet and Rack Installation 

Each model of the DM series LCD monitor has a series of holes located on the rear of the 

front panel for mounting the monitor to a rack or cabinet. 

 

NOTE:

 

1. The DM-190 monitor requires two special mounting brackets for installation 

into a rack or cabinet. Refer to Section 

5

5.5.2.2 for details. 

2. The DM-84 monitor uses panel mounting clamps for installation into a rack or 

cabinet. Refer to Section 

5

5.5.1.1 for details. 

3. The DM-65 monitor uses panel mounting clamps for installation into a rack or 

cabinet. Refer to Section 

5

5.5.1.2 for details. 

 

Summary of Contents for DM series

































































































































Reviews:

No comments