manualshive.com logo in svg

IEI Technology DM series, User Manual, Page: 39 / 128

Share
Download
IEI Technology DM series User Manual Download Page 39

 

 

DM Series Monitor 

Page 25

2.5 Optional Mounting Kits 

The following sections describe the various optional mounting kits available for each 

model of the DM series LCD monitor. Refer to 

Section 5.5

 for detailed instructions on the 

different mounting methods for the monitors. 

 CAUTION: 

Due to safety concerns, it is highly recommended to use the VESA mounting 

kits provided by IEI for wall, stand and arm mounting. If the VESA mounting kit 

is purchased separately, please make sure the mounting kit is UL-listed. 

2.5.1 DM-65 Mounting Kits 

5

Table 2-3

 lists the mounting kits available for the DM-65 monitor. 

Model 

DM-65 

Panel Mounting Kit 

Included 

Rack Mounting Kit 

RK-065MS-R10 

Wall Mounting Kit 

WK-065MS-R10 

DIN Mounting Kit 

DK-065MS 

LCD Monitor Arm 

ARM-11 

LCD Monitor Stand 

STAND-100-RS 

Table 2-3: DM-65 Mounting Kits

2.5.2 DM-84 Mounting Kits 

5

Table 2-4

 lists the mounting kits available for the DM-84 monitor. 

Model 

DM-84 

Panel Mounting Kit 

PK-84M 

Rack Mounting Kit 

RK-084MS-R10 

Wall Mounting Kit 

WK-084MS-R10 

DIN Mounting Kit 

DK-084MS 

Summary of Contents for DM series

































































































































Reviews:

No comments