background image

 

 
 

 

 

 

ZSSC4151Evaluation Kit Start-Up Guide       

© 2016 Integrated Device Technology, Inc. 

12 

March 11, 2016 

Document Revision History 

Revision 

Date 

Description 

1.00 

September 14, 2015 

First release. 

 

March 11, 2016 

Changed to IDT branding. 

 

 

 

Corporate Headquarters 

6024 Silver Creek Valley Road 

San Jose, CA 95138 

www.IDT.com

 

 

 

Sales 

1-800-345-7015 or 408-284-8200 

Fax: 408-284-2775 

www.IDT.com/go/sales

 

 

 

Tech Support 

www.IDT.com/go/support

  

 

 

DISCLAIMER Integrated Device Technology, Inc. (IDT) reserves the right to modify the products and/or specifications described herein at any time, without notice, at IDT's sole discretion. Performance 

specifications and operating parameters of the described products are determined in an independent state and are not guaranteed to perform the same way when installed in customer products. The 

information contained herein is provided without representation or warranty of any kind, whether express or implied, including, but not limited to, the suitability of IDT's products for any particular purpose, an 

implied warranty of merchantability, or non-infringement of the intellectual property rights of others. This document is presented only as a guide and does not convey any license under intellectual property 

rights of IDT or any third parties. 

 

IDT's products are not intended for use in applications involving extreme environmental conditions or in life support systems or similar devices where the failure or malfunction of an IDT product can be 

reasonably expected to significantly affect the health or safety of users. Anyone using an IDT product in such a manner does so at their own risk, absent an express, written agreement by IDT. 

 

Integrated Device Technology, IDT and the IDT logo are trademarks or registered trademarks of IDT and its subsidiaries in the United States and other countries. Other trademarks used herein are the 

property of IDT or their respective third party owners. For datasheet type definitions and a glossary of common terms, visi

www.idt.com/go/glossary

. All contents of this document are copyright of Integrated 

Device Technology, Inc. All rights reserved. 

Summary of Contents for ZSSC4151













Reviews: