background image

9

 

IDS LCD Keypad User Manual   700-292-01C   Issued March 2009 

If the partition is already STAY armed, this key will initialize AWAY arming. It is therefore possible to 

change directly from STAY armed to AWAY armed. 

 

2.2                                       Stay Arming                                           

 

Stay arming allows the user to monitor selected perimeter zones and bypass interior zones. The user can 

remain on the premises with access to designated areas during the STAY ARM cycle. Any zone which 

may be violated accidentally should be programmed as a buzz zone. When violated, a buzz zone will 

cause the keypad buzzer to sound for thirty seconds before sounding the siren. Entering a valid user 

code before the siren sounds, prevents an alarm condition from being registered and will silence the 

keypad buzzer and prevent the siren from sounding. 

 

To provide greater flexibility the panel caters for the programming of two different STAY PROFILES. Each 

STAY PROFILE contains a unique combination of STAY, BUZZ and ALARM zones which cater for a 

particular STAY ARM requirement. 

The profile number is now indicated at the end of the top line after the armed partition on the LCD 

Keypad when the panel is stay armed. 

 

Example:       

PROFILE 1 might be used when the family goes to bed in the evening. In this profile, some interior zones 

may be programmed as alarm zones or buzz zones, whereas PROFILE 2 is utilised while watching 

television when all interior zones would be bypassed. (See 9.1 How to Select a Stay Profile.) 

 

2.2.1                                                How to Stay Arm                                                      

 

[#] + [USER CODE] (Do not leave premises) 

 

1.

 

Select the required STAY PROFILE. (See Section 8.1) 

2.

 

Ensure that the LCD display reads 'Ready to arm' alongside the partition number being armed. If 

not, check that all protected doors and windows are closed and that all movement has ceased in 

the areas covered by motion detectors. 

3.

 

Press the [#] key. 

4.

 

Enter a valid [USER CODE]. If an incorrect code is entered, the keypad will give an error beep. In 

the event of an error press the [#] key and re-enter the [USER CODE]. 

5.

 

DO NOT violate the Entry/Exit zone (normally the front door). If the Entry/Exit zone is violated the 

system will arm in the AWAY mode. 

6.

 

The LCD Keypad will read 'Exit Delay', the ARM indicator will come on and the keypad buzzer will 

sound for the duration of the exit delay. 

7.

 

When the panel arms, any STAY zones will be automatically bypassed. These are displayed on 

the LCD Display as solid text. Any violated zones will be displayed on the LCD Display as 

flashing text. To scroll through zones which have been bypassed or violated use the [PANIC] and 

[MED] keys. 

8.

 

Ensure that you enter only those areas that are bypassed. 

 

2.2.2                                     Quick Stay Arm - Shortcut Key                                              

 

(Hold down the [5] key for 2 seconds until the keypad buzzer sounds) 

 

It is possible to STAY arm by holding down the 

[5]

 key until the keypad buzzer sounds. The panel will 

immediately arm into the stay mode without any exit delay. Holding the

 

[5] 

key again will toggle between 

the 2 stay profiles. 

Summary of Contents for LCD Digital Keypad

































Reviews: