idp SMART-21S User Manual Download

Page: 50 / 63

DeviceCon Error

THIS FEATURE IS NOT SUPPORTED IN SMART-21.

Lami Error

THIS FEATURE IS NOT SUPPORTED IN SMART-21.

Flipper Error

THIS FEATURE IS NOT SUPPORTED IN SMART-21.

Ribbon Zero

All ribbons are used

-. Install the new ribbon after purchasing it in the place of purchase

RibbonNotFound

Ribbon is not installed or not searched

-. Install a ribbon if not

-. Check usage of a genuine ribbon

TPH Not Found

Thermal Print Head is not installed or not recognized

-. Check the print head installation

-. Contact the place of purchase

TPH Over Heat

Thermal Print Head is overheated

-. Lower the temperature when the temperature of circumstance is too high

-. Take a stop for 10 minutes and print again.

-. Contact the place of purchase if this message is shown regularly

Invalid Data

Error occurs when the abnormal printing data is transmitted.

-. Replace the USB cable USB

-. Change the USB port in the PC

-. Reinstall the printer driver

Wrong Password

The password is not correct

-. Input the correct password

-. Contact the place of purchase if you forget the password

SetCommandFail

Failed to execute a command of the printer

-. Replace the USB cable USB

-. Change the USB port in the PC

-. Turn off/on the printer

Spool Full

The printing data is full in the spooler

-. This message disappear after printing all data to send

-. Turn off/on the printer if the spool data is full without printing

Summary of Contents for SMART-21S
































































Search results

Summary of Contents for SMART-21S

Reviews:

Related manuals for SMART-21S

Brands by name

Popular brands

idp SMART-21S, User Manual

Search results

Summary of Contents for SMART-21S

Reviews:

Related manuals for SMART-21S

Brands by name

Popular brands