manualshive.com logo in svg

idp SMART-21S, User Manual

Share
Download
idp SMART-21S User Manual Download Page 11

11 

1.3  Ribbon cartridge features 

 

 

Figure 6 Ribbon cartridge features 

 

①

    Ribbon cartridge 

-. Install a ribbon and a disposable cleaning roller provided with the ribbon. 

-. In the case of SMART-21 RW model, a ribbon is not used, and a disposable 

cleaning roller is only installed and used. 

-. This semi-permanent ribbon cartridge is a component of the printer. Printer does 

not operate if it is broken or damaged. In this case, please contact printer reseller.

 

 

②

 

③

  Take up & Supply parts 

-. Ribbon is wrapped to the supply parts as the Picture. It should be installed as the 

Figure.6 

 

④

  Disposable cleaning roller 

-. It removes dust on the surface of card to improve print quality before the card is 

printed. It should be changed together with the ribbon.   

-. After installing the disposable cleaning roller to the ribbon cartridge, peel off the 

protective film. 

-. It is provided with the ribbon. 

-. In the case of SMART-21 RW model, you have to purchase the disposable 

cleaning roller from the reseller.

 

 

 

①

 

Ribbon cartridge 

 

②

 

Take up parts 

 

③

 

Supply parts 

 

④

 

Disposable cleaning 
roller 

① 

②

 

③

 

④

 

Summary of Contents for SMART-21S
































































Reviews:

No comments

Brands by name

Popular brands

Load more brands