background image

0901082 Rev: D (08/08) 

Page 2 of 12 

TABLE OF CONTENTS 

 

Declaration of Conformity ..................................................................................... 3 

Introduction ........................................................................................................... 4 

Circuit Board Diagram........................................................................................... 4 

Installation............................................................................................................. 5 

Plumbing............................................................................................................... 5 

Probe Installation .................................................................................................. 6 

Electrical ............................................................................................................... 6 

Rinse Operation .................................................................................................... 7 

Probe Operation.................................................................................................... 8 

Probeless Operation ............................................................................................. 9 

Wiring Diagram ................................................................................................... 10 

Assembly Diagram.............................................................................................. 11 

Warranty Information .......................................................................................... 12 

Knight Locations ................................................................................................. 12 

 

 

EQUIPMENT RATINGS 

This includes equipment supply, description of I/O connections, duty cycle and operating environmental conditions.  

• 

Pollution degree 2;  

• 

Installation category 2;  

• 

Altitude 2000 m;  

• 

Humidity 50% to 80%  

• 

Electrical supply 120, 208, or 240 Vac, 50/60 Hz;  

• 

Indoor use statement;  

• 

Temperature 5°C to 40°C;  

• 

Statement  advising  that  mains  supply  voltage  fluctuations  are  not  to  exceed  10  percent  of  the  nominal  supply 
voltage. 

CAUTION: Wear protective clothing and eyewear when dispensing chemicals or 
other materials. Observe safety handling instructions (MSDS) of chemical mfrs. 

CAUTION:  To  avoid  severe  or fatal  shock,  always  disconnect main  power when 
servicing the unit. 

CAUTION:  When  installing  any  equipment,  ensure  that  all  national  and  local 
safety, electrical, and plumbing codes are met. 

Summary of Contents for Knight Ultra Micro-Pro UMP 100 Series













Reviews: