background image

0901082 Rev: D (08/08) 

Page 12 of 12 

DISCLAIMER 

Knight  LLC  does  not  accept  responsibility  for  the  mishandling,  misuse,  or  non-performance  of  the  described  items 
when  used  for  purposes  other  than  those  specified  in  the  instructions.  For  hazardous  materials  information  consult 
label,  MSDS,  or  Knight  LLC.  Knight  products  are  not  for  use  in  potentially  explosive  environments.  Any  use  of  our 
equipment  in  such  an  environment  is  at  the  risk  of  the  user,  Knight  does  not  accept  any  liability  in  such 
circumstances. 

WARRANTY 

All  Knight  controls  and  pump  systems  are  warranted  against  defects  in  material  and  workmanship  for  a  period  of 
ONE  year.  All  electronic  control  boards  have  a  TWO  year  warranty.  Warranty  applies  only  to  the  replacement  or 
repair of such parts when returned to factory with a Knight Return Authorization (KRA) number, freight prepaid, and 
found  to  be  defective  upon  factory  authorized  inspection.  Bearings  and  pump  seals  or  rubber  and  synthetic  rubber 
parts such as “O” rings, diaphragms, squeeze tubing, and gaskets are considered expendable and are not covered 
under  warranty.  Warranty  does  not  cover  liability  resulting  from  performance  of  this  equipment  nor  the  labor  to 
replace this equipment. Product abuse or misuse voids warranty. 

FOOTNOTE 

The  information  and  specifications  included  in  this  publication  were  in  effect  at  the  time  of  approval  for  printing. 
Knight, LLC reserves the right, however, to discontinue or change specifications or design at any time without notice 
and without incurring any obligation whatsoever. 

Knight Headquarters 

Tel: 949.595.4800 

Fax: 949.595.4801 

USA Toll Free 

Tel: 800.854.3764 

Fax: 800.752.9518 

Knight Canada 

Tel: 905.542.2333 

Fax: 905.542.1536

Knight Europe 

Tel: 44.1293.615.570 

Fax: 44.1293.615.585

Knight Australia 

Tel: 61.2.9725.2588 

Fax: 61.2.9725.2025 

Knight N. Asia 

Tel: 82.2.3481.6683 

Fax: 82.2.3482.5742 

Knight S. Asia 

Tel: 65.6763.6633 

Fax: 65.6764.4020 

KNIGHT LLC,   

KNIGHT LLC,   

KNIGHT LLC,   

KNIGHT LLC,   

A Unit of IDEX Corporation  (www.knightequip.com)

 

Summary of Contents for Knight Ultra Micro-Pro UMP 100 Series













Reviews: