background image

European Standards

CE Statement

Conforms where applicable to European Union (EU) Low Voltage Directive (LVD) 2014/35/EU, Electromagnetic
Compatibility (EMC) Directive 2014/30/EU, Radio Equipment Directive (RED)2014/53/EU and RoHS Recast
(RoHS2) Directive: 2011/65/EU + Amendment Directive (EU) 2015/863.

This equipment complies with the rules, of the Official Journal of the European Union, for governing the Self
Declaration of the CE Marking for the European Union as specified in the above directive(s).

WEEE

Information on Disposal for Users of Waste Electrical & Electronic Equipment

This symbol on the product(s) and / or accompanying documents means that used electrical and electronic
products should not be mixed with general household waste. For proper treatment, recovery and recycling, please
take this product(s) to designated collection points where it will be accepted free of charge.

Alternatively, in some countries you may be able to return your products to your local retailer upon purchase of an
equivalent new product.

Disposing of this product correctly will help save valuable resources and prevent any potential negative effects on
human health and the environment, which could otherwise arise from inappropriate waste handling.

Please contact your local authority for further details of your nearest designated collection point.

Penalties may be applicable for incorrect disposal of this waste, in accordance with your national legislation.

For business users in the European Union

If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further
information.

Information on Disposal in other Countries outside the European Union

This symbol is only valid in the European Union. If you wish to discard this product please contact your local
authorities or dealer and ask for the correct method of disposal.

EN50131 Standards

This component meets the requirements and conditions for full compliance with EN50131 series of standards for
equipment classification.

EN 50131-1:2006+A2:2017, EN 50131-3:2009, EN 50131-6:2008+A1:2014, EN 50131-10:2014, EN 50136-1:2012, EN
50136-2:2013, EN 60839-11-1:2013

Security Grade 4
Environmental Class II

Equipment Class: Fixed
Readers Environmental Class: IVA, IK07
SP1 (PSTN – voice protocol)
SP2 (PSTN – digital protocol)
SP6 (LAN – Ethernet) and DP1 (LAN – Et PSTN)
SP6 (LAN – Ethernet) and DP1 (LAN – Et USB-4G modem)

Tests EMC (operational

) according to EN 55032:2015

Radiated disturbance

EN 55032:2015

Power frequency magnetic field immunity tests

(EN 61000-4-8)

EN50131

In order to comply with EN 50131-1 the following points should be noted:

PRT-HZX16-DIN | Protege Half DIN Rail 16 Input Expander | Installation Manual

22

Summary of Contents for PRT-HZX16-DIN








































Reviews: