manualshive.com logo in svg

ICS CWS-200, Operator'S Manual, Page: 4 / 20

Share
Download
ICS CWS-200 Operator'S Manual Download Page 4

© 2010 ICS, Blount International Inc.  Specifications are subject to change without notice.  REV0810  F/N 542025

TITLE

CWS-200 OPERATOR’S MANUAL

4

WA

RNIN

G

• Do NO

T operate the machine without side co

ver or gua

rd

 en

cl

osure installed.

• Do NO

T tension chain,

 install or remo

ve guide ba

r, chain or side co

ver without po

wering off 

hy

draulic suppl

y.

• Fa

ilure to observe these precautions can result in serious injury

.

F/N 541814

• Do NOT exceed hydraulic flow of 25 

gpm (95 lpm) at 2500 psi (172.5 bar) 
hydraulic pressure.

• Do NOT operate the machine if the 

work piece, rail and/or machine are 
not properly supported and secured.

• Do NOT operate with machine 

directly over head.

• ALWAYS disengage the machine 

from the rail before repositioning or 
removing.

• Fluids escaping under pressure can 

penetrate the skin.

• Failure to observe these precautions 

can result in serious injury.

WARNING

F/N 541813

Valve Knob must be in 

center “OFF” position 

before powering on 

hydraulic supply.

WARNING

F/N 541812

PRIMARY COMPONENTS

PRIMARY MACHINE COMPONENTS

WARNING LABEL LOCATIONS

WATER SUPPLY

HANDLE FRAME

GUARD CLAMP BRACKETS

GUARD ENCLOSURE

VALVE KNOB

TRAVERSE

CARRIAGE

SIDE COVER

SIDE COVER BASE

HYDRAULIC HOSE

CONNECTIONS

ROTATION CONTROLS

TRAVERSE CONTROLS

1

2

3

Summary of Contents for CWS-200





















Reviews:

No comments