ICS Schneider Messtechnik Anton Paar DMA 501 Instruction Manual And Safety Information Download Page 6

1 Safety Instructions

6

E15IB001EN-N

• Before you start a measurement or cleaning

procedure, check the injection adapters for leak
tightness.

• Take measures that spilled liquids cannot get

into plug connections or venting slots of electri-
cal appliances.

• Install the instrument so that you can easily

separate it from the mains supply (pull the
power plug) at any time.

Precautions for flammable samples and 
cleaning agents

• Keep potential sources of ignition, like sparks or

open flames, at a safe distance from the instru-
ment.

• Place the instrument on a laboratory bench

made of fireproof material, preferably bricks,
ceramics, or stoneware.

• Store only the minimum required amount of

sample, cleaning agents, and other flammable
materials near the instrument.

• Do not spill sample/cleaning agents or leave

their containers uncovered. Immediately
remove spilled sample/cleaning agents.

• Ensure that the setup location is sufficiently

ventilated. The environment of the instrument
must be kept free of flammable gases and
vapors.

• Provide fire-extinguishing equipment.

Transportation

• Empty the measuring cell and all hoses before

you move or lift the instrument.

• To carry the instrument, put one hand into the

recessed grip below the front, and grasp the
metal ledge on the rear with the other hand.

• Do not hold the instrument by its bottom to

avoid squeezing your fingers when you put
down the instrument.

• Carry the instrument in front of you and keep it

close to your body.

1.3  Service and Repairs

• Service and repair procedures may be carried

out only by authorized persons or by Anton Paar
GmbH.

1.4  Disposal

• Concerning the disposal of the instrument,

observe the legal requirements in your country.

1.5  Conventions for Safety Messages

The following conventions for safety messages are 
used in this document:

WARNING

Description of risk

Warning indicates a hazardous situation which, if 
not avoided, 

could

 result in death or serious 

injury.

CAUTION

Description of risk

Caution indicates a hazardous situation which, if 
not avoided, could result in minor or moderate 
injury.

NOTICE

Description of risk

Notice indicates a situation which, if not avoided, 
could result in damage to property.

Summary of Contents for Anton Paar DMA 501



























Reviews: