7
• With the nozzle removed, check that both chemicals flow with
equivalent force.
• Partial or complete blockage of one chemical port will result in
off-ratio adhesive.
*Handi-Gun
®
being shown for reference only.
Crunchy, friable, slow or non curing.
Darker brown in color.
“A-Rich” Adhesive:
Softer, white colored adhesive, with
shrinkage.
“B-Rich” Adhesive:
70
21
85
29
All Handi-Gun
®
nozzles are easily cleanable and solvent resistant. To clean nozzles,
liquid chemical must be dissolved prior to its complete chemical reaction by flushing the
nozzle with Polysolv or other suitable solvent. Gun face can be kept clean with the use of
petroleum jelly on the face or with a soft cloth to remove residue. Cleaning a nozzle more
than twice is not recommended.
Polysolv
Apply a small amount of petroleum jelly,
which is provided with each kit, to help keep
the gun face clean from cured adhesive or
contamination that could block one of the
chemical ports. Change nozzles frequently!
Adhesive will cure inside the nozzle in the
same amount of time that adhesive becomes
tack-free in the air.
Nozzle Care and Usage
Temperature and Storage
Chemical temperature is very important, store kits at or above
70°F (21°C) prior to use. Cold chemical may lead to off-ratio flow.
Optimum chemical temperature is 70–85°F (21–29°C), see TDS for
formula specific temperature recommendations.
A-component chemical may eventually
harden and clog the hose if stored for
too long. Gun is disposable and is not
intended for continuous re-use. For best
results, dispense liquid from hose at
least once every 3 days. Use contents
within 30 days of initial use.
Always read all operating, application and safety instructions before using any products from ICP Adhesives & Sealants, Inc. Use in conformance with all local, state and federal
regulations and safety requirements. Failure to strictly adhere to any recommended procedures and reasonable safety precautions shall release ICP Adhesives & Sealants, Inc. of
all liability with respect to the materials or the use thereof. For additional information and location of your nearest distributor, call ICP Adhesives & Sealants, Inc. 330.753.4585.
NOTE:
Physical properties shown are typical and are to serve only as a guide for engineering design. Results are obtained from specimens under ideal conditions and may vary
upon use, temperature and ambient conditions. Right to change physical properties as a result of technical progress is reserved. This information supersedes all previously
published data.Yields shown are optimum and will vary slightly depending on ambient conditions and particular application. Read all product directions and safety information
before use. This product is organic, and therefore, is combustible. Consult local building codes for specific requirements regarding the use of cellular plastics or urethane foam
adhesive in construction.
Important
WARNINGS:
Polyset
®
adhesive products are composed of a diisocyanate, hydrofluorocarbon blowing agent and polyol. Consult the product’s SDS (available at www.icpadhesives.
com) for specific information. The urethane foam adhesive produced from these ingredients will support combustion and may present a fire hazard if exposed to a fire or excessive
heat about 240°F (116°C). Wear protective glasses with side shields or goggles, nitrile gloves, and clothing that protects against dermal exposure. Recommend using in a well
ventilated area with certified respiratory protection or a powered air purifying respirator (PAPR). For more information regarding a certified respiratory program please visit
http://www.cdc.gov/niosh/. To view or receive a copy of ICP Adhesives & Sealants, Inc.’s respirator program, please contact ICP Adhesives & Sealants, Inc. Customer Care at
1.800.321.5585. Personal Protective Equipment can be purchased through ICP Adhesives & Sealants, Inc. distribution by purchasing the Polyset
®
Contractor Safety Kit (F65251).
The Contractor Safety Kit includes: nitrile gloves, contractor safety glasses, and a NIOSH approved negative pressure half mask respirator. For professional use only. WARNING:
Non-Flammable Compressed Gas. Keep away from heat. Smoking and open flames, including hot work, should be prohibited in the vicinity of a foaming operation. Avoid contact
with skin and eyes. May cause sensitiza- tion by inhalation and/or direct skin contact. Avoid prolonged or repeated breathing of vapor.
KEEP OUT OF REACH OF CHILDREN.
FIRST AID:
In any first aid case CONSULT A PHYSICIAN. EYES: Flush with water for at least 15 minutes. SKIN: Remove contaminated clothing. Wash skin with plenty of soap and
water. Cured adhesive must be removed manually. INHALATION: If breathing is difficult, give oxygen. If breathing has stopped, give artificial respiration. INGESTION: give large
quantities of water. Do NOT induce vomiting. Contact a physician immediately in any first aid situation. Consult the product’s SDS (available at www.icpadhesives.com) for specific
information. Contents: polymeric diisocyanate, hydrofluorocarbon blowing agent, polyol, amine catalyst.
Warnings
The Manufacturer warrants only that the product shall meet its specifications: this warranty is in lieu of all other written or unwritten, expressed or implied warranties and The
Manufacturer expressly disclaims any warranty of merchantability, or fitness for a particular purpose. The buyer assumes all risks whatsoever as to the use of the material.
Buyer’s exclusive remedy as to any breach of warranty, negligence or other claim shall be limited to the replacement of the material. Failure to strictly adhere to any recommended
procedures shall release the Manufacturer of all liability with respect to the materials of the use thereof. User of this product must determine suitability for any particular purpose,
including, but not limited to, structural requirements, performance specifications and application requirements prior to installation and after product has been properly applied.
Limited Warranty
Polyset
®
Spray Foam Adhesive products are composed of a diisocyanate, hydrofluorocarbon blowing agent and polyol. Consult the product’s SDS (available at www.icpadhesives.com) for specific
information. The urethane foam adhesive produced from these ingredients will support combustion and may present a fire hazard if exposed to a fire or excessive heat about 240°F (116°C). Wear
protective glasses or goggles, nitrile gloves, and clothing that protects against dermal exposure. Use only in a well ventilated area with certified respiratory protection or a powered air purifying respirator
(PAPR). See SDS (available at www.icpadhesives.com) for specific information. For professional use only.
