background image

 

NOVA-7895 Socket 370 Celeron

 TM

 & Pentium III 

®

                          

Multimedia & Dual Ethernet ,IEEE1394,  Embedded Board 

11

2.2   NOVA-7895 Dimensions ( Unit : mm ) 

 

 

NOVA-7895 Socket 370 Celeron

 TM

 & Pentium III 

®

                          

Multimedia & Dual Ethernet ,IEEE1394,  Embedded Board 

12

2.3  Unpacking Precautions 

 

Some of the components on the NOVA-7895 are very sensitive to 
static electric charges and can be damaged by a sudden rush of 
power. To protect them from accidental damage, please be sure to 
follow these precautions: 

 

 

Ground yourself to remove any static charge before touching your 
NOVA-7895. You can do it by using a grounded wrist strap at all 
times or by frequently touching any conducting materials that are 
connected to the ground. 

 

 

Handle your NOVA-7895 at the edges. Don’t touch IC chips, leads 
or circuitry if not necessary. 

 

 

Do not plug in any connector or jumper while the power is on.

 

 

 

Do not put your NOVA-7895 unprotected on a flat surface as it has 
sensitive components on both sides.  

 

2.4   Clear CMOS Setup 

If you forget the CMOS password, you can clear or reset it by 
closing the 

JP6

. After JP6 (1-2) is closed, turn on the power for 

about 3 seconds then turn it off and re-open the JP6 (1-2). Now, 
the password has been cleared from your CMOS. 

 

 JP6 : Clear CMOS  Setup 

 



 

 

PIN NO. 

DESCRIPTION 

2-3 

Normal Operation 

1-2 

Clear CMOS Setup 

 

Summary of Contents for NOVA-7895

















































Reviews: