ICP Electronics NOVA-7895 Page 30 User Manual Download | Manualshive

Page: 30 / 48

background image

NOVA-7895 Socket 370 Celeron

TM

& Pentium III

®

Multimedia & Dual Ethernet ,IEEE1394, Embedded Board

57

ACPI Function

This item allows you to enable/disable the Advanced Configuration and
Power Management (ACPI).
The choice: Enabled, Disabled.

ACPI Suspend Type

This item allows you to S1(Power ON Suspend) the Advanced
Configuration and Power Management (ACPI).
The choice: S1(POS)

Video Off Option

When enabled, this feature allows the VGA adapter to operate in a power saving
mode.

Always On

Monitor will remain on during power saving modes.

NOVA-7895 Socket 370 Celeron

TM

& Pentium III

®

Multimedia & Dual Ethernet ,IEEE1394, Embedded Board

58

Suspend --> Off

Monitor blanked when the systems enters the Suspend
mode.

Susp,Stby -->
Off

Monitor blanked when the system enters either Suspend or
Standby modes.

All Modes -->
Off

Monitor blanked when the system enters any power saving
mode.

Video Off Method

This determines the manner in which the monitor is blanked.

V/H
SYNC+Blank

This selection will cause the system to turn off the vertical
and horizontal synchronization ports and write blanks to the
video buffer.

Blank Screen

This option only writes blanks to the video buffer.

DPMS

Select this option if your monitor supports the Display
Power Management Signalling (DPMS) standard of the
Video Electronics Standards to select video power
management values.

Switch Function

You can choose whether or not to permit your system to enter complete Suspend
mode. Suspend mode offers greater power savings, with a correspondingly
longer awakening period.

The choice: Break/Wake, Disabled.

Hot Key Function As

Select

Enabled

if your system has a hot key for soft power off.

The choice: Enabled, Disabled.

HDD Off After

«
...
28
29
30
31
32
...
»

Summary of Contents for NOVA-7895

















































Reviews:

No comments

Related manuals for NOVA-7895

ITX-945GC3B N330

Brand: OEM Pages: 38

Altera Lark Board

Brand: Embest Pages: 9

Brand: BESTEK Pages: 52

Brand: Advantech Pages: 90

Brand: Freetech Pages: 48

Brand: AOpen Pages: 8

Brand: DFI Pages: 120

Brand: Gigabyte Pages: 18

EVAL-6ED100HPDRIVE-AS

Brand: Infineon Pages: 14

Brand: ASROCK Pages: 244

Brand: Semtech Pages: 16

Z87 Extreme9/ac

Brand: ASROCK Pages: 116

Brand: EVGA Pages: 128

Brand: DFI Pages: 177

Brand: MSI Pages: 77

R3288LC-2N Series

Brand: JETWAY Pages: 44

Brand: Texas Instruments Pages: 23

Brand: TYAN Pages: 70

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands