background image

 

NOVA-7895 Socket 370 Celeron

 TM

 & Pentium III 

®

                          

Multimedia & Dual Ethernet ,IEEE1394,  Embedded Board 

49

This item defines the Data-in to PRE command period. 

The choice: 1T, 2T 

VCM REF To ACT/REF Delay 

This item defines VCM REF to REF/ACT command period.  

The choice: 10T, 9T. 

VCM ACCT To ACT/REF Delay 

This item defines VCM ACT to ACT/REF command period.  

The choice: 10T, 9T, 8T, Reserved. 

Early CKE Delay 1T Control 

This option is used when the system operates under low frequency and CKE 
delay adjustment method defined in the 'Early CKE Delay Adjustment' which can 
not meet setup time and hold time requirement. 

The choice: Normal, Delay 1T.  

Early CKE Delay Adjust 

This item controls the timing for CKE. Various delay options are provided to 
ensure that CKE can meet SDRAM setup time and hold time specification when 
CKE is driven out. 

The Choice: 1ns, 2ns, 3ns, 4ns, 5ns, 6ns, 7ns, 8ns. 

Mem. Command Output Time 

This item is to control the timing to drive memory command onto the memory bus.   

The choice: Normal, Delay 1T. 

SDRAM/VCM CAS Latency 

When synchronous DRAM is installed, the number of clock cycles of CAS latency 
depends on the DRAM timing. 

NOVA-7895 Socket 370 Celeron

 TM

 & Pentium III 

®

                          

Multimedia & Dual Ethernet ,IEEE1394,  Embedded Board 

50

The Choice: 2, 3 , SPD 

SDRCLK Control 

This item controls the phase of SDRCLK that lags behind SDCLK. 

The choice: Enabled, Disabled. 

SDWCLK Control CS#/CKE 

This item controls the phase of SDWCLK used for chip set select signals pin that 
lags ahead SDCLK. 

The choice:  Enabled, Disabled. 

SDWCLK Control MA/SRAS 

This item controls the phase of SDWCLK used for MA/ SRAS signals that lags 
ahead SDCLK. 

The choice:  +5.0ns~-2.5ns (Default 0.0ns) 

SDWCLK Control DQM/MD 

This item controls the phase of SDWCLK used for DQM/MD signals that lags 
ahead SDCLK. 

The choice:  +5.0ns~-2.5ns (Default 0.0ns) 

 

EGMRCLK Control 

This item controls the phase of EGMRCLK that lags behind SDCLK. 

The choice:  -1.0ns~+6.5ns (Default 0.0ns)

 

EGMWCLK Control 

This item controls the phase of EGMWCLK that lags ahead SDCLK. 

The choice:  +5.0ns~-2.5ns (Default 0.0ns) 
 

Summary of Contents for NOVA-7895

















































Reviews: