manualshive.com logo in svg

ICP DAS USA tM-TH8, User Manual

Share
Download
ICP DAS USA tM-TH8 User Manual Download Page 59

 
 

tM-TH8 User Manual, Rev: A1.1  7MH-018-A11 

59 

 
 
 

2.14 $AAI 

 

Description: 

Reads the INIT status of a module. 

 
Syntax: 

$AAI[CHKSUM](CR) 

$ 

Delimiter character 

AA 

Address of the module to be diagnosed (00 to FF) 

I 

Command to read the module INIT status 

 
Response: 

Valid command: 

!AAS[CHKSUM](CR)

 

Invalid command: 

?AA[CHKSUM](CR)

 

! 

 

Delimiter character for a valid command 

? 

 

Delimiter character for an invalid command 

AA   

Address of the responding module (00 to FF) 

S       

INIT switch status of the module 
0: The INIT switch is moved to the INIT 

position 

1: The INIT switch is moved to the Normal 

position 

 
There will be no response if the command syntax is 
incorrect, there is a communication error, or there is no 
module with the specified address. 

tM-TH8 

 

 

Summary of Contents for tM-TH8













































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands