background image

P9 

Caution

 

 

 

 
 

1. 

Danger 

 

The meter contains hazardous voltages, and should never be disassembled. 

Failing to follow this practice will result in serious injury or death. Any work on 
or  near  energized  meters,  meter  sockets,  or  other  metering  equipment  could 
induce  a  danger  of  electrical  shock.  It  is  strongly  recommended  that  all  work 
should  be  performed  only  by  qualified  industrial  electricians  and  metering 
specialist. ICP DAS assumes no responsibility if your electrical installer does not 
follow the appropriate national and local electrical codes.   

2. 

Warning   

ICP DAS assumes no liability for any damage resulting from the use of this 

product. ICP DAS reserves the right to change this manual at any time without 
notice.  The  information  furnished  by  ICP  DAS  is  believed  to  be  accurate  and 
reliable. However, no  responsibility is assumed by ICP DAS for its use, not for 
any infringements of patents or other rights of third parties resulting from its 
use.   

3. 

  Product Warranty & Customer Support

 

ICP  DAS  warrants  all  products  free  from  defects  in  material  and 

workmanship  for  a  period  of  one  year  from  the  date  of  shipping.  During  the 
warranty period, we will, at our position, either repair or replace any product 
that  proves  to  be  defective.  To  report  any  defect,  please  contact 

+886-3- 

597-3366 or [email protected]. Please have the model name, serial number 
and  a  detailed  problem  description  available  when  you  call.  If  the  problem 
concerns a particular reading, please have all meter readings available. When 
returning any merchandise to ICP DAS, a return SN. is required.

 

 

Summary of Contents for iWSN-9601 Series










Reviews: