Icom IC-F70DS Instruction Manual Download

Page: 10 / 48

PANEL DESCRIPTION

■

Function display

SIGNAL STRENGTH INDICATOR

Indicates relative signal strength level.

LOW POWER INDICATOR

Appears when low output power is selected.

AUDIBLE INDICATOR

➥

Appears when the channel is in the ‘audible’ (unmute)

condition.

➥

Appears when the specified 2/5-tone/BIIS code is

received.

COMPANDER INDICATOR

Appears when the compander function is activated.

SCRAMBLER INDICATOR

Appears when the voice scrambler function is activated.

BELL INDICATOR

Appears/blinks when the specific 2/5-tone/BIIS code is
received, according to the pre-programming.

CALL CODE MEMORY INDICATOR

Appears when the call code memory is selected.

SDM MEMORY INDICATOR

Appears when the SDM memory is selected.

BATTERY INDICATOR

Appears or blinks when the battery power decreases to a
specified level.

ALPHANUMERIC DISPLAY

➥

Displays an operating channel number, channel name,
Set mode contents, DTMF code, etc.

➥

The indication mode can be selected from 1 line or 2
lines. Ask your dealer for details.

• In this instruction manual, the LCD illustration is described

using the 2 lines indication mode.

KEY INDICATOR

Indicate the programmed function of the front panel keys
([P0], [P1], [P2] and [P3]).

IC-F70_F80-1.qxd 05.1.18 4:26 PM Page 6 (1,1)

Summary of Contents for IC-F70DS

















































Search results

Summary of Contents for IC-F70DS

Reviews:

Related manuals for IC-F70DS

Brands by name

Popular brands

Icom IC-F70DS, Instruction Manual

Search results

Summary of Contents for IC-F70DS

Reviews:

Related manuals for IC-F70DS

Brands by name

Popular brands