background image

8

2

OPERATION

Receiving and transmitting

RECEIVING:

q

Push [

] to turn the power ON.

w

Push 

[

]

and 

[

]

to select a channel.

e

When receiving a call, adjust the audio output level to a
comfortable listening level.

TRANSMITTING:

r

Take the microphone off hook.

• 2-tone, 5-tone mute may be released. (The ‘audible’ condition is

selected and “

” appears.)

• A priority channel may be selected automatically.

t

Wait for the channel to become clear.

• The channel is busy when “

” appears.

y

Push the 

[CALL]

key when initiating a call from your side.

• Coded audio may be heard from the transceiver, then “

appears.

• This operation may not be necessary depending on your signal-

ing system. Contact your dealer.

u

While pushing and holding [PTT], speak into the micro-
phone at your normal voice level.

i

Release [PTT] to receive.

IMPORTANT!:

To maximize the readability of your signal;

Pause briefly after pushing [PTT].

Hold the microphone 2 to 5 cm from your mouth, then
speak into the microphone at a normal voice level.

D

Transmitting notes

• Transmit inhibit function

The transceiver has several inhibit functions which restrict
transmission under the following conditions:

- The channel is in mute condition (‘Inaudible’ condition; “

” does

not appear).

- Channel is busy.
- A matched/un-matched CTCSS code is received.
- The selected channel is a ‘receive only’ channel.

• Time-out timer

After continuous transmission for a pre-programmed period,
the time-out timer is activated causing the transceiver to stop
transmitting and automatically select receive.

• Penalty timer

Once the time-out timer is activated, transmission is further
inhibited for a period determined by the penalty timer.

IC-F110_F210_EUR-1.qxd  03.2.5 3:31 PM  Page 8 (1,1)

Summary of Contents for IC-F110

























Reviews: