background image

20

6

CE

DECLARATION

OF CONFORMITY

We Icom Inc. Japan

1-1-32, Kamiminami, Hirano-ku
Osaka 547-0003, Japan

Kind of equipment:

     

UHF TRANSCEIVER

This compliance is based on conformity with the following harmonised
 standards, specifications or documents:

i)   EN 301 489-1 (August 2000)

ii)  EN 301 489-5 (August 2000)

iii) EN 60950 (August 1992 +A11)  

iv) EN 300 086-2 (March 2001) 

v)  EN 300 219-2 (March 2001)

Type-designation: 

      

iC-f210

Signature

Authorized representative name

Place and date of issue

Düsseldorf 15th Jan. 2003

Declare on our sole responsibility that this equipment complies with the
essential requirements of the Radio and Telecommunications Terminal 
Equipment Directive, 1999/5/EC, and that any applicable Essential Test
Suite measurements have been performed.

Version (where applicable):

0168

440  490 MHz  12.5 kHz/ 25 kHz
440  490 MHz  12.5 kHz/ 20 kHz
400  430 MHz  12.5 kHz/ 25 kHz

About e-marking:

Detailed installation notes for Icom

mobile transceivers to be fitted into vehicles are available.
Please contact your Icom dealer or distributor.

IC-F110_F210_EUR-1.qxd  03.2.5 3:31 PM  Page 20 (1,1)

Summary of Contents for IC-F110

























Reviews: