162
14
SET MODE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
5SER"AND%DGE
7.
This “User Band Edge” item appears only when “ON
5SER vORh5SER/. 48vISSELECTEDINTHEh"AND
Edge Beep” item. (p. 161)
7HENYOUSELECTh/.5SER vORh/.5SER 48vIN
the “Band Edge Beep” item, you can program a total
of 30 band edge frequencies in this item. See page 42
for programming details.
"EEP3OUND-!).
8.
$EFAULT(Z
Set a desired beep frequency for the MAIN Band to
between 500 Hz and 2000 Hz in 10 Hz steps.
9OUCANSETTHEBEEPOUTPUTLEVELIN
the “Beep Level”
item. (p. 161)
"EEP3OUND35"
9.
$EFAULT(Z
Set a desired beep frequency for the SUB Band to be-
tween 500 Hz and 2000 Hz in 10 Hz steps.
9OUCANSETTHEBEEPOUTPUTLEVELIN
the “Beep Level”
item. (p. 161)
2&31,#ONTROL
10.
$EFAULT2&31,
Set the [RF/SQL] control operation.
s!54/
;2&31,= FUNCTIONS AS ONLY AN 2&
GAINCONTROLIN33"#7AND2449A
squelch control in AM, FM and DV.
s31,
;2&31,=FUNCTION
s as a squelch con-
trol.
s2&31, ;2&31,=FUNCTION
s as a noise squelch
or an
3METERSQUELCHIN&-ONLY
as
an S-meter squelch in SSB, CW,
2449
,
AM and DV.
-ETER0EAK(OLD
11.
$EFAULT/.
Turn the Meter Peak Hold function ON or OFF.
When this function is set to ON, the peak level of a re-
ceived signal strength or the output power is displayed
for approximately 0.5 seconds.
&-$6#ENTER%RROR
12.
$EFAULT/.
Turn the FM and DV center error detection ON or
OFF.
When an off-frequency signal is received, the MAIN
and SUB Band’s TX/RX indicators blink.
4IME/UT4IMER
13.
$EFAULT/&&
To prevent a prolonged transmission, the transceiver
has a Time-Out Timer function.
If a continuous transmission exceeds the set period,
the transmission will be cut off.
Set the time period to 3, 5, 10, 20 or 30 minutes, or
turn OFF the Time-Out Timer function.
044,OCK
14.
$EFAULT/&&
Turn the PTT Lock function ON or OFF.
To prevent accidental transmissions, this function in-
hibits transmitting, when turned ON.
1UICK30,)4
15.
$EFAULT/.
Turn the Quick Split function ON or OFF.
When this item is set to ON, hold down [SPLIT] for 1
second to shift the transmit frequency from the receive
frequency, according to the “SPLIT Offset” option as
described below. See page 83 for details.
30,)4/FFSET
16.
$EFAULT-(Z
Set the offset* for the quick split function.
*The difference between transmit and receive frequencies.
The frequency offset can be set to between –9.999
MHz and +9.999 MHz in 1 kHz steps.
SPLIT LOCK
17.
$EFAULT/&&
Turn the Split Lock function ON or OFF.
When this item is set to ON, you can use [MAIN DIAL]
to adjust the transmit frequency while holding down
[XFC], even while the Dial Lock function is enabled.
See pages 82, 83 for split frequency operation de-
tails.
