8
SET MODE
8-3
Function
Beep Level
(Default: 50%)
Sets the beep output level.
L
If the “Beep (Confirmation)” item is set to “OFF,” no
beep sounds.
Beep Level Limit
(Default: ON)
Selects whether or not to limit the volume up to the
specified level.
Beep (Confirmation)
(Default: ON)
Turns the Confirmation beep ON or OFF.
L
If the “Beep Level” item is set to “0%,” no beep sounds.
Bmnd Edge Beep
(Default: ON (Default))
Turns the Band Edge beep ON or OFF.
Innormmtion
L
•
If the “Beep Level” item is set to “0%,” no beep sounds.
• When you tune into an amateur band’s frequency
range, the Band Edge high beep sounds.
• When you tune out of an amateur band’s frequency
range, the Band Edge low beep sounds.
RF/SQL Control
(Default: RF+SQL)
Set the
AF
RF/SQL
(outer) control operation.
MF Bmnd ATT
(Default: ON)
Turns the MF Band Attenuator function ON or OFF.
This function adds approximately 16 dB of attenuation
to prevent a desired signal from becoming distorted
when very strong MF band signals are received.
This function is usable when the frequency is set to
between 0.03000 and 1.59999 MHz, for only receiving.
L
When you receive a weak signal on the MF band,
select “OFF.”
L
The 16 dB of the MF band attenuation is added to
any other attenuation value that you have set.
TX Delmy HF
(Default: OFF)
TX Delmy 50M
(Default: OFF)
TX Delmy 70M*
(Default: OFF)
Sets the TX delay time on the HF, 50 or 70 MHz band.
L
If an external equipment’s rise time is slower than
that of the IC-7300, a reflected wave is produced
and it may damage the IC-7300. To prevent this, set
the appropriate delay time so that no reflected wave
is produced.
L
Select “OFF” for no rise speed.
* Depending on the transceiver’s version, this item may not
be displayed.
Time-Out Timer (CI-V)
(Default: OFF)
Sets the Time-out Timer for CI-V operation.
This setting is valid only transmitting initiated by a
CI-V command or pushing
TRANSMIT
.
L
Select “OFF” for no time limit.
Quick SPLIT
(Default: ON)
Turns the Quick Split function ON or OFF.
FM SPLIT Onnset (HF)
(Default: –0.100 MHz)
FM SPLIT Onnset (50M)
(Default: –0.500 MHz)
Sets the frequency offset for the Split function in the
FM mode on the HF or 50 MHz band.
SPLIT LOCK
(Default: OFF)
Turns the Split Lock function ON or OFF.
[TUNER] Switch
(Default: Auto)
Selects whether or not to save the internal antenna
tuner’s status after pushing
TUNER
on each band.
PTT Stmrt
(Default: OFF)
Turns the PTT Start Tuning function ON or OFF.
<<Preset Memory Clemr>>
Clears the all of the internal antenna tuner preset
points.
RTTY Mmrk Frequency
(Default: 2125)
Selects the RTTY mark frequency.
L
When the internal RTTY decoder is used, 2125 Hz
is automatically selected.
RTTY Shint Width
(Default: 170)
Selects the RTTY shift width.
L
When the internal RTTY decoder is used, 170 Hz is
automatically selected.
RTTY Keying Polmrity
(Default: Normal)
Selects the RTTY keying polarity.
SPEECH Lmngumge
(Default: English)
Selects the speech language.
SPEECH Speed
(Default: Fast)
Selects the speech speed.
