Icom IC-706MKIIG Instruction Manual Download

Page: 60 / 75

TIIN

The following chart is designed to help you correct
problems which are not equipment malfunctions.

If you are unable to locate the cause of a problem or
solve it through the use of this chart, contact your
nearest Icom Dealer or Service Center.

PROBLEM

POWER SUPPLY

RECEIVE

POSSIBLE CAUSE

SOLUTION

REF.

Power does not come
on when the [POWER]
switch is pushed.

No sound comes from
the speaker.

Sensitivity is low.

Receive audio is distor-
ted.

Receive signal is distor-
ted with strong signals.

DC power cable is improperly
connected.

Fuse is blown.

Battery is exhausted if you are using
a 12 V battery as the power source.

Reconnect the power cable correctly.

Check for the cause, then replace the
fuse with a spare one.

(Fuses are installed in two places. One is
installed in the DC power cable and the
other is installed in the PA unit.

Check the battery voltage with the
[POWER] pushed IN.

p. 13

p. 56

—

p. 1

—

p. 12

—

p. 14

pgs. 27,
28

p. 21

p. 19

p. 20

p. 21

Volume level is set too low.

The squelch is closed.

The transceiver is in the transmitting
condition.

An external speaker or headphones
are connected.

The antenna is not connected properly.

The antenna feed line is cut or shorted.

The antenna for another band is
selected.

The antenna is not properly tuned.

The attenuator function is activated.

The operating mode is not selected
correctly.

The [SHIFT] control is set off-center.

Noise blanker function is activated.

Preamp is activated.

Rotate [AF] clockwise to obtain a suit-
able listening level.

Rotate [SQL] counterclockwise to
open the squelch.

Release [PTT] on the microphone or
check the SEND line of an external
unit, if connected.

Check the external speaker or head-
phone plug connection.

Check the speaker ON/OFF switch or
speaker A/B switch, when an optional
SP-20

EXTERNAL SPEAKER

is in use.

Reconnect to the antenna connector.

Check the feed line and correct any
improper conditions.

Select an antenna suitable for the
operating frequency.
Make sure that [ANT1] is used for
frequencies less than 60 MHz and
[ANT2] is used for frequencies of 60
MHz and above.

Push [TUNE] to manually tune the
antenna.

Push [ATT] to turn the function OFF.

Select a suitable operating mode.

Set [SHIFT] to the center position.

Push [

] to turn the function OFF.

Push [P.AMP] to turn the function
OFF.

IC-706MKIIG.qxd 02.3.27 13:53 Page 57

Summary of Contents for IC-706MKIIG












































































Search results

Summary of Contents for IC-706MKIIG

Reviews:

Related manuals for IC-706MKIIG

Brands by name

Popular brands

Icom IC-706MKIIG, Instruction Manual

Search results

Summary of Contents for IC-706MKIIG

Reviews:

Related manuals for IC-706MKIIG

Brands by name

Popular brands