27
4
RECEIVE AND TRANSMIT
The AT-180 automatic antenna tuner matches the IC-
706MKIIG to the connected antenna automatically.
Once the tuner matches an antenna, the variable
capacitor angles are memorized as a preset point for
each frequency range (100 kHz steps). Therefore,
when you change the frequency range, the variable
capacitors are automatically preset to the memorized
point.
N
No
otte
e::
• The AT-180 cannot be used for the 144/430 MHz
band.
• When operating on the 144/430 MHz band, push-
ing the tuner switch selects the call channel (p. 39).
• The AT-180 can match both HF and 50 MHz bands.
However, operation is different for the HF and 50
MHz bands.
T
TU
UN
NE
ER
R O
OP
PE
ER
RA
AT
TIIO
ON
N
•
F
Fo
orr tth
he
e H
HF
F b
ba
an
nd
d::
Push [TUNER] to turn the tuner ON. The antenna is
tuned automatically during transmission when the
antenna SWR is higher than 1.5:1.
• When the tuner is OFF, the [TUNER] light goes out.
•
F
Fo
orr tth
he
e 5
50
0 M
MH
Hz
z b
ba
an
nd
d::
Push and hold [TUNER] to tune the antenna. If the
[TUNER] light flashes slowly while transmitting, push
and hold [TUNER] again to re-tune the antenna.
M
MA
AN
NU
UA
AL
L T
TU
UN
NIIN
NG
G
During SSB operation on HF bands at low voice lev-
els, the AT-180 may not be tuned correctly. In such
cases, manual tuning is helpful.
Push and hold [TUNER] for 1 sec. to start manual tun-
ing.
• CW mode is selected, a side tone is emitted, and the
[TUNER] light flashes; then, the previous mode is select-
ed.
If the tuner cannot reduce the SWR to less than 1.5:1
after 20 sec. of tuning, the [TUNER] light goes out. In
this case, check the following:
• the antenna connection and feedline
• the antenna SWR (p. 26; meter function)
T
Th
hrro
ou
ug
gh
h iin
nh
hiib
biitt
(HF bands only)
The AT-180 has a through inhibit condition. When
selecting this condition, the tuner can be used at
poor SWR’s. In this case, automatic tuning in the HF
bands activates only when exceeding SWR 3:1.
Therefore, manual tuning is necessary each time you
change the frequency. Although termed “through
inhibit,” the tuner will be “through” if the SWR is high-
er than 3:1 after tuning.
•
T
Tu
un
ne
err s
se
en
ns
siittiiv
ve
e c
co
on
nd
diittiio
on
n
(HF bands only)
If you require critical tuning at any time during trans-
mission, select the tuner sensitive condition. See
p. 55 for selection.
•
A
Au
utto
om
ma
attiic
c ttu
un
ne
err s
stta
arrtt
(HF bands only)
If you want to turn OFF the tuner under conditions of
VSWR 1.5:1 or less, use “automatic tuner on” and
turn the tuner OFF. See p. 54 for turning the function
ON and OFF.
D
O
Op
pttiio
on
na
all A
AT
T--1
18
80
0
A
AU
UT
TO
OM
MA
AT
TIIC
C A
AN
NT
TE
EN
NN
NA
A T
TU
UN
NE
ER
R
o
op
pe
erra
attiio
on
n
[TUNER/CALL]
Lights to indicate the AT-180
is turned ON.
[TUNER/CALL]
Flashes to indicate re-tuning
is necessary.
C
CA
AU
UT
TIIO
ON
N::
N
NE
EV
VE
ER
R
transmit with the tuner ON
when no antenna is connected. This will damage
both the transceiver and the antenna tuner.
[TUNER/CALL]
Push and hold for 1 sec. to start
manual tuning.
CONVENIENT
IC-706MKIIG.qxd 02.3.27 13:53 Page 27
