manualshive.com logo in svg

Iclebo Arte YCR-M05-02, User Manual

Share
Download
Iclebo Arte YCR-M05-02 User Manual Download Page 18

17

●

 C

he

ck

 b

efo

re

 re

pa

ir r

ep

or

t

●

 Display er

ror messa

ge

Noise of the 

robot cleaner is 

getting worse.

▶Dust bin is full or filter is 

   dirty.
▶Main brush is dirty.
▶Main brush is dirty or hairs 

   are accumulating between the 

   main brush and the bearing.

▶Empty and clean the dust bin.

▶See <Product control & maintenance> 

   (page 13) and clean the filter.

▶See <Product control & maintenance> 

   (page 14) and clean the main brush.

Error display

Cause

Solution

Lifted wheel

Move the robot cleaner to flat area in case 
the wheel is stuck on the threshold or porch.

Cannot detect floor

Move the robot cleaner to flat area.

Dust bin error

Dust bin is not properly assembled.
See <Product control & maintenance> and install properly.

Wheel motor overload

Check if foreign substance such as hair or lint exists 

on the wheel.

See <Product control & maintenance> and remove 

the foreign substance.

Brush motor overload

Check if foreign substance such as hair or 

lint exists on the main brush or side-brush.

See <Product control & maintenance> and remove 

the foreign substance.

Suction motor overload

See <Product control & maintenance> 
and clean filter, empty the dust bin.

Internal system error

Turn off the power switch of the robot cleaner 

then turn it on again.

Dust stuck on the 

front-wheel

Remove the front-wheel for cleaning then see 

<Product control & maintenance> to put it back.

Display error message

C 1

C 2

C 3

C 4

C 5

C 6

C 7

C 8

Summary of Contents for Arte YCR-M05-02






















Reviews:

No comments

Brands by name

Popular brands

Load more brands