background image

General information

5

IMPORTANT

 

Pay attention to sharp edges on the generator and its accessories.

 

The boiler must be kept sheltered from adverse weather conditions, with regard to the minimum temperature (-10 ° C) and 
from the rain.

 

The user is responsible for considering the seismic degree of the user area in the design of the heating plant.

 

After an earthquake, have technical personnel assess any damage by carrying out NDCs (non-destructive checks), if nec-
essary.

 

The manufacturer shall not be held liable in the event of accidents caused by incorrect decommissioning.

 

The personnel in charge must be able to prove to have sufficient knowledge and experience relating to the safety and 
control / regulation accessories supplied with the generator and good familiarity with the instructions contained in the use 
and maintenance manual and be capable and physically suitable.

 

During handling, always maintain a distance of at least 5 m from the projection of the appliance to the ground

 

In case of violent impact during handling, visually check the integrity of the appliance, all over; run the hydraulic test again.

 

The generators are sized only for loads due to pressure, temperature and contained fluid.

PROHIBITIONS

IT IS FORBIDDEN

 

Operate electrical devices or appliances such as switches, household appliances, etc. if you smell fuel or unburnt materials. 
In this case:

 

-

ventilate the room by opening doors and windows

 

-

close the fuel shut-off device

 

Perform any technical or cleaning intervention before disconnecting the appliance from the electrical power supply and 
wearing the Personal Protective Equipment (P.P.E. according to Italian Legislative Decree 81/08).

 

Modifying safety or adjustment devices without the boiler manufacturer’s authorisation and indications.

 

Plug or dimensionally reduce the ventilation openings of the installation room. The ventilation openings are essential for 
proper combustion.

 

Perform any welding/repairs. If necessary, contact the manufacturer/verifying party for operation (in Italy according to MD 
329/04).

 

Expose the generator to atmospheric agents.

 

Leave flammable substances and containers in the room where the appliance is installed.

 

Disperse the packaging material in the environment and leave it within the reach of children as it may be a potential source 
of danger. It must be disposed of in accordance with the legislation in force.

HAZARDS

DANGER

 

Dangers due to 

water leaks

. Disconnect the boiler from the electrical power supply, close the water supply and promptly 

contact the Technical Assistance Service Authorised 

ICI CALDAIE S.p.A.

 or professionally qualified personnel.

 

Danger of explosion.

 Routine and extraordinary maintenance must be entrusted to 

professionally qualified personnel

 

with the purpose of promptly detecting any damage to the generator's pressurised body and the safety and control ac-
cessories.

Cooke Industries - Phone: +64 9 579 2185    Email: [email protected]    Web: www.cookeindustries.co.nz

Summary of Contents for SIXEN









































Reviews: